Robot control

From Wikipedia, the free encyclopedia

Robot control is the theory of how to model and control robots.

A simplistic model of a robot is to look at as a collection of links connected by joints. The tip of the robot (the end-effector) is commonly referred to as the tool center point or TCP. As the joints rotate and the links contract and expand, the TCP will change position.

It is of great importance to know the position of the TCP in world coordinates. For example, for a robot to weld in a straight line, the actuators in the joints of the robot have to be controlled in a complex manner.

[edit] Denavit-Hartenberg convention

To facilitate calculations, engineers use the Denavit-Hartenberg convention(D-H) to help them describe the positions of links and joints unambiguously. Every link gets its own coordinate system. There are a few rules to consider in choosing the coordinate system:

the $z$ -axis is in the direction of the joint axis
the $x$ -axis is parallel to the common normal or if there is no common normal, $x_n = z_{n - 1} \times z_n$
the $y$ -axis follows from the $x$ - and $z$ -axis by choosing it to be a right handed coordinate system.

Every link/joint pair can be described as a coordinate transformation from the previous coordinate system to the next coordinate system.

${}^{n - 1}T_n = \operatorname{Rot}(z_{n - 1}, \theta_n) \cdot \operatorname{Trans}(z_{n - 1}, l_n) \cdot \operatorname{Trans}(x_n, d_n) \cdot \operatorname{Rot}(x_n, \alpha_n)$

Note that these are 2 screws after oneanother. See Screw (motion).

The matrices mentioned above are as follows:

$\operatorname{Rot}(z_{n - 1}, \theta_n) = \begin{pmatrix} \cos\theta_n & -\sin\theta_n & 0 & 0 \\ \sin\theta_n & \cos\theta_n & 0 & 0 \\ 0 & 0 & 1 & 0 \\ 0 & 0 & 0 & 1 \\ \end{pmatrix}$

$\operatorname{Trans}(z_{n - 1}, l_n) = \begin{pmatrix} 1 & 0 & 0 & 0 \\ 0 & 1 & 0 & 0 \\ 0 & 0 & 1 & l_n \\ 0 & 0 & 0 & 1 \\ \end{pmatrix}$

$\operatorname{Trans}(x_n, d_n) = \begin{pmatrix} 1 & 0 & 0 & d_n \\ 0 & 1 & 0 & 0 \\ 0 & 0 & 1 & 0 \\ 0 & 0 & 0 & 1 \\ \end{pmatrix}$

$\operatorname{Rot}(x_n, \alpha_n) = \begin{pmatrix} 1 & 0 & 0 & 0 \\ 0 & \cos\alpha_n & -\sin\alpha_n & 0 \\ 0 & \sin\alpha_n & \cos\alpha_n & 0 \\ 0 & 0 & 0 & 1 \\ \end{pmatrix}$

This gives:

$\operatorname{}^{n - 1}T_n = \begin{pmatrix} \cos\theta_n & -\sin\theta_n \cos\alpha_n & \sin\theta_n \sin\alpha_n & d_n \cos\theta_n \\ \sin\theta_n & \cos\theta_n \cos\alpha_n & -\cos\theta_n \sin\alpha_n & d_n \sin\theta_n \\ 0 & \sin\alpha_n & \cos\alpha_n & l_n \\ 0 & 0 & 0 & 1 \\ \end{pmatrix}$

Robot control

From Wikipedia, the free encyclopedia

[edit] Denavit-Hartenberg convention

Views

Navigation

Search