Magnetic refrigeration

From Wikipedia, the free encyclopedia

Magnetic refrigeration is a cooling technology based on the magnetocaloric effect. This technique can be used to attain extremely low temperatures (well below 1 kelvin), as well as the ranges used in common refrigerators, depending on the design of the system.

The fundamental principle was suggested by Debye (1926) and Giauque (1927)^{[ 1 ]} , and the first working magnetic refrigerators were constructed by several groups beginning in 1933. Magnetic refrigeration was the first method developed for cooling below about 0.3 kelvin (a temperature attainable by ³He/⁴He dilution refrigeration).

[edit] The magnetocaloric effect

The Magnetocaloric effect (MCE, from magnet and calorie) is a magneto-thermodynamic phenomenon in which a reversible change in temperature of a suitable material is caused by exposing the material to a changing magnetic field. This is also known as adiabatic demagnetization by low temperature physicists, due to the application of the process specifically to effect a temperature drop. In that part of the overall refrigeration process, a decrease in the strength of an externally applied magnetic field allows the magnetic domains of a chosen (magnetocaloric) material to become disoriented from the magnetic field by the agitating action of the thermal energy (phonons) present in the material. If the material is isolated so that no energy is allowed to (e)migrate into the material during this time (i.e. an adiabatic process), the temperature drops as the domains absorb the thermal energy to perform their reorientation. The randomization of the domains occurs in a similar fashion to the randomization at the curie temperature, except that magnetic dipoles overcome a decreasing external magnetic field while energy remains constant, instead of magnetic domains being disrupted from internal ferromagnetism as energy is added.

One of the most notable examples of the magnetocaloric effect is in the chemical element gadolinium and some of its alloys. Gadolinium's temperature is observed to increase when it enters certain magnetic fields. When it leaves the magnetic field, the temperature returns to normal.

[edit] Thermodynamic process

Analogy between magnetic refrigeration and vapor cycle or conventional refrigeration. H = externally applied magnetic field; Q = heat quantity; P = pressure; ΔT_ad = adiabatic temperature variation

The process is performed as a refrigeration cycle, analogous to the Carnot cycle, and can be described at a starting point whereby the chosen working substance is introduced into a magnetic field (i.e. the magnetic flux density is increased). The working material is the refrigerant, and starts in thermal equilibrium with the refrigerated environment.

• Adiabatic magnetization: The substance is placed in an insulated environment. The increasing external magnetic field (+H) causes the magnetic dipoles of the atoms to align, thereby decreasing the material's magnetic entropy and heat capacity. Since overall energy is not lost (yet) and therefore total entropy is not reduced (according to thermodynamic laws), the net result is that the item heats up (T + ΔT_ad).

• Isomagnetic enthalpic transfer: This added heat can then removed by a fluid like water or helium for example (-Q). The magnetic field is held constant to prevent the dipoles from reabsorbing the heat. Once sufficiently cooled, the magnetocaloric material and the coolant are separated (H=0).

• Adiabatic demagnetization: The substance is returned to another adiabatic (insulated) condition so the total entropy remains constant. However, this time the magnetic field is decreased, the thermal energy causes the domains to overcome the field, and thus the sample cools (i.e. an adiabatic temperature change). Energy (and entropy) transfers from thermal entropy to magnetic entropy (disorder of the magnetic dipoles).

• Isomagnetic entropic transfer: The magnetic field is held constant to prevent the material from heating back up. The material is placed in thermal contact with the environment being refrigerated. Because the working material is cooler than the refrigerated environment (by design), heat energy migrates into the working material (+Q).

Once the refrigerant and refrigerated environment are in thermal equilibrium, the cycle begins anew.

[edit] Applied technique

The basic operating principle of an ADR is the use of a strong magnetic field to control the entropy of a sample of material, often called the "refrigerant". Magnetic field constrains the orientation of magnetic dipoles in the refrigerant. The stronger the magnetic field, the more aligned the dipoles are, and this corresponds to lower entropy and heat capacity because the material has (effectively) lost some of its internal degrees of freedom. If the refrigerant is kept at a constant temperature through thermal contact with a heat sink (usually liquid helium) while the magnetic field is switched on, the refrigerant must lose some energy because it is equilibrated with the heat sink. When the magnetic field is subsequently switched off, the heat capacity of the refrigerant rises again because the degrees of freedom associated with orientation of the dipoles are once again liberated, pulling their share of equipartitioned energy from the motion of the molecules, thereby lowering the overall temperature of a system with decreased energy. Since the system is now insulated when the magnetic field is switched off, the process is adiabatic, i.e. the system can no longer exchange energy with its surroundings (the heat sink), and its temperature decreases below its initial value, that of the heat sink.

The operation of a standard ADR proceeds roughly as follows. First, a strong magnetic field is applied to the refrigerant, forcing its various magnetic dipoles to align and putting these degrees of freedom of the refrigerant into a state of lowered entropy. The heat sink then absorbs the heat released by the refrigerant due to its loss of entropy. Thermal contact with the heat sink is then broken so that the system is insulated, and the magnetic field is switched off, increasing the heat capacity of the refrigerant, thus decreasing its temperature below the temperature of the He heat sink. In practice, the magnetic field is decreased slowly in order to provide continuous cooling and keep the sample at an approximately constant low temperature. Once the field falls to zero (or to some low limiting value determined by the properties of the refrigerant), the cooling power of the ADR vanishes, and heat leaks will cause the refrigerant to warm up.

[edit] Working materials

The magnetocaloric effect is an intrinsic property of a magnetic solid. This thermal response of a solid to the application or removal of magnetic fields is maximized when the solid is near its magnetic ordering temperature.

The magnitudes of the magnetic entropy and the adiabatic temperature changes are strongly dependent upon the magnetic order process: the magnitude is generally small in antiferromagnets, ferrimagnets and spin glass systems; it can be substantial for normal ferromagnets which undergo a second order magnetic transition; and it is generally the largest for a ferromagnet which undergoes a first order magnetic transition.

Also, crystalline electric fields and pressure can have a substantial influence on magnetic entropy and adiabatic temperature changes.

Currently, alloys of gadolinium producing 3 to 4 K per tesla of change in a magnetic field can be used for magnetic refrigeration or power generation purposes.

Recent research on materials that exhibit a giant entropy change showed that Gd₅(Si_xGe_{1 − x})₄, La(Fe_xSi_{1 − x})₁₃H_x and MnFeP_{1 − x}As_x alloys, for example, are some of the most promising substitutes for Gadolinium and its alloys (GdDy, GdTy, etc...). These materials are called giant magnetocaloric effect materials (GMCE).

Gadolinium and its alloys are the best material available today for magnetic refrigeration near room temperature since they undergo second-order phase transitions which have no magnetic or thermal hysteresis involved.

[edit] Paramagnetic salts

The originally suggested refrigerant was a paramagnetic salt, such as cerium magnesium nitrate. The active magnetic dipoles in this case are those of the electron shells of the paramagnetic atoms.

In a paramagnetic salt ADR, the heat sink is usually provided by a pumped ⁴He (about 1.2 K) or ³He (about 0.3 K) cryostat. An easily attainable 1 tesla magnetic field is generally required for the initial magnetization. The minimum temperature attainable is determined by the self-magnetization tendencies of the chosen refrigerant salt, but temperatures from 1 to 100 mK are accessible. Dilution refrigerators had for many years supplanted paramagnetic salt ADRs, but interest in space-based and simple to use lab-ADRs has recently revived the field (for example see http://www.cmr.uk.com/abcmrhis.html).

Eventually paramagnetic salts become either diamagnetic or ferromagnetic, limiting the lowest temperature which can be reached using this method.

[edit] Nuclear demagnetization

One variant of adiabatic demagnetization that continues to find substantial research application is nuclear demagnetization refrigeration (NDR). NDR follows the same principle described above, but in this case the cooling power arises from the magnetic dipoles of the nuclei of the refrigerant atoms, rather than their electron configurations. Since these dipoles are of much smaller magnitude, they are less prone to self-alignment and have lower intrinsic minimum fields. This allows NDR to cool the nuclear spin system to very low temperatures, often 1 µK or below. Unfortunately, the small magnitudes of nuclear magnetic dipoles also makes them less inclined to align to external fields. Magnetic fields of 3 teslas or greater are often needed for the initial magnetization step of NDR.

In NDR systems, the initial heat sink must sit at very low temperatures (10–100 mK). This precooling is often provided by the mixing chamber of a dilution refrigerator or a paramagnetic salt ADR stage.

[edit] Commercial development

This refrigeration, once proven viable, could be used in any possible application where cooling, heating or power generation is used today. Since it is only at an early stage of development, there are several technical and efficiency issues that should be analyzed. The magnetocaloric refrigeration system is composed of pumps, electric motors, secondary fluids, heat exchangers of different types, magnets and magnetic materials. These processes are greatly affected by irreversibilities and should be adequately considered. Appliances using this method could have a smaller environmental impact if the method is perfected and replaces hydrofluorocarbon (HFCs) refrigerators (some refrigerators still use HFCs which have some greenhouse effect). At present, however, the superconducting magnets that are used in the process have to themselves be cooled down to the temperature of liquid nitrogen, or with even colder, and relatively expensive, liquid helium. Considering these fluids have boiling points of 77.36 K and 4.22 K respectively, the technology is clearly not cost-efficient and efficient for home appliances, but for experimental, laboratorial, and industrial use only.

Recent research on materials that exhibit a large entropy change showed that Gd₅(Si_xGe_{1 − x})₄, La(Fe_xSi_{1 − x})₁₃H_x and MnFeP_{1 − x}As_x alloys are some of the most promising substitutes of Gadolinium and its alloys (GdDy, GdTy, etc...). Gadolinium and its alloys are the best material available today for magnetic refrigeration near room temperature. There are still some thermal and magnetic hysteresis problems to be solved for them to become really useful and scientist are working hard to achieve this goal. A good review on magnetocaloric materials is entitled "Recent developments in magnetocaloric materials" and written by Dr. Gschneidner et at.[5]

Recent discovery has succeeded using commercial grade materials and permanent magnets on room temperatures to construct a magnetocaloric refrigerator which promises wide use.

This technique has been used for many years in cryogenic systems for producing further cooling in systems already cooled to temperatures of 4 kelvins and lower (see adiabatic demagnetization). In England, a company called Cambridge Magnetic Refrigeration produces cryogenic systems based on the magnetocaloric effect.

[edit] Current and future uses

There are still some thermal and magnetic hysteresis problems to be solved for these first-order phase transition materials that exhibit the GMCE to become really useful; this is a subject of current research. A useful review on magnetocaloric materials is entitled "Recent developments in magnetocaloric materials" and written by Dr. Gschneidner et al.[6]

This effect is currently being explored to produce better refrigeration techniques, especially for use in spacecraft. This technique is already used to achieve cryogenic temperatures in the laboratory setting (below 10K). As an object displaying MCE is moved into a magnetic field, the magnetic spins align, lowering the entropy. Moving that object out of the field allows the object to increase its entropy by absorbing heat from the environment and disordering the spins. In this way, heat can be taken from one area to another. Should materials be found to display this effect near room temperature, refrigeration without the need for compression may be possible, increasing energy efficiency.

[edit] History

The effect was discovered in pure iron in 1881 by E. Warburg. Originally, the cooling effect varied between 0.5 to 2 K/T.

Major advances first appeared in the late 1920s when cooling via adiabatic demagnetization was independently proposed by two scientists: Debye (1926) and Giauque (1927).

The process was demonstrated a few years later when Giauque and MacDougall in 1933 used it to reach a temperature of 0.25 K. Between 1933 and 1997, a number of advances in utilization of the MCE for cooling occurred.

This cooling technology was first demonstrated experimentally by chemist Nobel Laureate William F. Giauque and his colleague Dr. D.P. MacDougall in 1933 for cryogenic purposes (they reached 0.25 K)[7].

Between 1933 and 1997, a number of advances occurred which have been described in some reviews:

^{[1] [2] [3] [4]}

In 1997, the first near room temperature proof of concept magnetic refrigerator was demonstrated by Prof. Karl A. Gschneidner, Jr. by the Iowa State University at Ames Laboratory. This event attracted interest from scientists and companies worldwide who started developing new kinds of room temperature materials and magnetic refrigerator designs.

Refrigerators based on the magnetocaloric effect have been demonstrated in laboratories, using magnetic fields starting at 0.6 T up to 10 teslas. Magnetic fields above 2 T are difficult to produce with permanent magnets and are produced by a superconducting magnet (1 tesla is about 20,000 times the Earth's magnetic field).

[edit] Room temperature devices

Some recent research has focused on the use of the process to perform refrigeration near "room temperature". Constructed examples of room temperature magnetic refrigerators are listed in the table below:

In one example, Prof. Karl A. Gschneidner, Jr. unveiled a proof of concept magnetic refrigerator near room temperature in February 20, 1997. He also announcement the discovery of the giant MCE (GMCE) in Gd₅Si₂Ge₂ on June 9, 1997 [8] (see below). Since then, hundreds of peer-reviewed articles have been written describing materials exhibiting magnetocaloric effects.

[edit] References

• Lounasmaa, Experimental Principles and Methods Below 1 K, Academic Press (1974).

• Richardson and Smith, Experimental Techniques in Condensed Matter Physics at Low Temperatures, Addison Wesley (1988).

[edit] Notes

1. ^ Zemansky, Mark W.. Temperatures, 50. ISBN 048624072.

1. ^ Gschneidner K A Jr and Pecharsky V K 1997 Rare Earths: Science, Technology and Applications III ed R G Bautista et al (Warrendale, PA: The Minerals, Metals and Materials Society) p 209
2. ^ Pecharsky V K and Gschneidner K A Jr 1999 J. Magn. Magn. Mater. 200 44
3. ^ Gschneidner K A Jr and Pecharsky V K 2000 Annu. Rev. Mater. Sci. 30 387
4. ^ Gschneidner K A Jr and Pecharsky V K 2002 Fundamentals of Advanced Materials for Energy Conversion ed D Chandra and R G Bautista (Warrendale, PA: The Minerals, Metals and Materials Society) p 9
5. ^ Zimm C, Jastrab A, Sternberg A, Pecharsky V K, Gschneidner K Jr, Osborne M and Anderson I, Adv. Cryog. Eng. 43, 1759 (1998).
6. ^ Bohigas X, Molins E, Roig A, Tejada J and Zhang X X, IEEE Trans. Magn. 36 538 (2000).
7. ^ Hirano N, Nagaya S, Takahashi M, Kuriyama T, Ito K and Nomura S 2002 Adv. Cryog. Eng. 47 1027
8. ^ Rowe A M and Barclay J A, Adv. Cryog. Eng. 47 995 (2002).
9. ^ Rowe A M and Barclay J A, Adv. Cryog. Eng. 47 1003 (2002).
10. ^ Richard M A, Rowe A M and Chahine R, J. Appl. Phys. 95 2146 (2004).
11. ^ Zimm C, Paper No K7.003 Am. Phys. Soc. Meeting, March 4, Austin, TX (2003) [1]
12. ^ Wu W, Paper No K7.004 Am. Phys. Soc. Meeting, March 4, Austin, TX (2003) [2]
13. ^ Hirano N, Paper No K7.002 Am. Phys. Soc. Meeting March 4, Austin, TX, [3]
14. ^ Hirano N, Paper No K7.002 Am. Phys. Soc. Meeting March 4, Austin, TX, [4]
15. ^ Clot P, Viallet D, Allab F, Kedous-LeBouc A, Fournier J M and Yonnet J P, IEEE Trans. Magn. 30 3349 (2003).

[edit] See also

• Thermoacoustic refrigeration
• Dilution refrigerator

[edit] External links

• NASA - How does an Adiabatic Demagnetization Refrigerator Work ?
• Magnetocaloric effect
• What is magnetocaloric effect and what materials exhibit this effect the most?
• Magnetocaloric materials keep fridges cool by C. Wu
• Ames Laboratory news release, May 25, 1999, Work begins on prototype magnetic-refrigeration unit.
• Magnetic refrigerator successfully tested
• Refrigeration Systems Terry Heppenstall's notes, University of Newcastle Upon Tyne (November 2000)
• XRS Adiabatic Demagnetization Refrigerator
• Executive Summary (.doc format) A Continuous Adiabatic Demagnetization Refrigerator (google cache)